Features
- Corrugated furnaces on ASME Section I high pressure boilers
- Large furnace volume for complete combustion
- Lower emissions and high efficiency
- Exceptional efficiencies and economical operation
Construction
- Handholes for waterside access
- Factory installed gas train avail w/ FM, GE-GAP, NFPA-85, UL and other approvals
- Structural steel skid avail w/ opt. removable skids, jacking pads and seismic design
- Front/Rear door gaskets made of ceramic fiber
- Industrial grade, space saving, one-piece rear door
Quality
To make the highest quality scotch marine boiler on the market, we began with quality-in-design. The tube sheet, furnace, tubes and other critical components are designed to exceed the ASME code to provide longevity, reliability, efficiency, and quality.
These components include:
- Tubesheets exceeding the ASME code thickness by 25% in low pressure units
- Tubesheets exceed ASME code by 33% in high pressure units
- Tubesheets come with standard 3/4″” ligament spacing.
- Tubes 10% thicker than ASME code requirements
- Furnace is 21% greater in size than other boilers, in both length and diameter,
-Furnace designed to contain flame and protect rear tubesheet against overheating.
- High pressure steam boilers include a corrugated furnace
- Corrugated furnace combats the negative effects of expansion and contraction.
Whether we are cutting steel, welding tubesheets to pressure vessels, insulating pressure vessels with two inch 8-lb density mineral fiber, painting galvanized 22 gauge steel jackets with 500°F enamel or piping a gas train, we tailor our products to exceed ASME standards.
Safety
Packaged boilers are trimmed with necessary safeties and code piping and signed off on by code inspectors. Factory mounted and wired, proven and reliable packaged burners are available from your choice of burner manufacturer. All Superior packaged firetube boilers are low fire tested and can be full factory firetested to check electrical components for proper operation, ensure smooth ignition, and allow quicker field startups.
DETAILS
Capacity: 100 - 2,500 HP
Fuel Capabilities: #2 Oil, Hydrogen, Natural Gas, Propane
Pass: 2-pass
Tube Type: Rifled Tubes
Steam Design Pressure: 15 - 300 psig
Hot Water Design Pressure: 30 - 160 psig
Kiowa Waste Heat
General Description
Kiowa Single Pass Heat Recovery only units are designed with 2” & 2 .5” heat transfer tubes.
Features
- Customized design engineered for your specific solution.
- Available with dual chamber design or supplemental firing
- 1,800°F maximum inlet temperature
- Roller-bearing supported single-hinged rear door for total fireside access
- Typical applications: high particulate levels, low gas side pressure drop, high steam design pressures, inlet temperatures to 1800° F
Construction
- 12 gauge tubes
- 3/4″ tube sheets with 3/4″ ligament spacing
- 2", 2.5", or 3" tubes
- Furnaces thicker than ASME code requirements
- Corrugated to help reduce the stresses associated with expansion and contraction
Quality
All Waste Heat Recovery Boilers are made with 12 gauge tubes, 3/4” tube sheets with 3/4” ligament spacing and furnaces thicker than ASME code requirements. All section I furnaces above 24” diameter are corrugated to help reduce the stresses associated with expansion and contraction.
Safety
Superior’s Waste Heat Recovery Boilers are trimmed and equipped with safeguards and code piping. Each boiler is inspected by independent code inspectors. Factory mounted and wired packaged burners are available from all burner manufacturers for supplemental firing.
DETAILS
Capacity: Customized for job specific conditions, with experience in designing units over 40,000 lb/hr.
Fuel Capabilities: Customized for application
Pass: 1-pass
Tube Type: Smooth Tubes or Rifled Tubes
Steam Design Pressure: 150 - 300 psig
Hot Water Design Pressure: Section I vessels 150 - 250 psig
Mohawk
Features
- Large single furnace dryback design with exceptional efficiencies and economical operation
- Corrugated furnaces on ASME Section I high pressure boilers
- Generous furnace volume for low heat releases & ultra low NOx compliance
- Exceptional efficiencies and economical operation
- Roller-bearing supported single-hinged rear door for total fireside access
- Available with NOx reduction technology to sub 9 ppm
Construction
- Handholes for waterside access
- Factory installed gas train available with FM, GE-GAP, NFPA-85, UL and other approvals
- Structural steel skid available with optional removable skids, jacking pads and seismic design
- Front/Rear door gaskets made of ceramic fiber
- Industrial grade, space saving, one-piece rear door
Quality
To make the highest quality scotch marine boiler on the market, we began with quality-in-design. The tube sheet, furnace, tubes and other critical components are designed to exceed the ASME code to provide longevity, reliability, efficiency, and quality.
These components include:
- Tubesheets exceed ASME code thickness by 25% in low pressure units
- Tubesheet exceeding ASME code thickness by 33% in high pressure units
- Tubesheets come with standard 3/4″ ligament spacing.
- Tubes 10% thicker than ASME code requirements
- Furnace is 21% greater in size than other boilers, in both length and diameter,
- Furnace designed to contain the flame within
- Furnace designed to protect rear tubesheet against overheating.
- High pressure steam boilers include a corrugated furnace
- Corrugated furnace combats the negative effects of expansion and contraction.
Whether we are cutting steel, welding tubesheets to pressure vessels, insulating pressure vessels with two inch 8-lb density mineral fiber, painting galvanized 22 gauge steel jackets with 500°F enamel or piping a gas train, we tailor our products to exceed ASME standards.
Safety
Packaged boilers are trimmed with necessary safeties and code piping and signed off on by code inspectors. Factory mounted and wired, proven and reliable packaged burners are available from your choice of burner manufacturer. All Superior packaged firetube boilers are low fire tested and can be full factory firetested to check electrical components for proper operation, ensure smooth ignition, and allow quicker field startups.
DETAILS
Capacity: 30 - 1,000 HP
Fuel Capabilities: #2 Oil, Bio-Diesel, Digester Gas, Heavy-Oil, Hydrogen, Natural Gas, Propane, Syngas
Pass: 3-pass
Tube Type: Smooth Tubes
Steam Design Pressure: 15 - 300 psig
Hot Water Design Pressure: 30 - 160 psig
